新聞中心
使用滾珠絲杠時須提供良好的潤滑！
來源：http://www.zhzdh888.com/ 日期：2023-06-06 發布人：
1）請仔細擦拭防銹油并封入潤滑劑后再使用。
1) Please carefully wipe the anti rust oil and seal it with lubricant before use.
2）導軌絲杠廠家提醒您，請避免將不同的潤滑劑混合使用。即使增稠劑相同的潤滑脂，由于添加劑等不同，也可能相互之間產生不良影響。
2) The guide screw manufacturer reminds you to avoid mixing different lubricants. Even lubricating greases with the same thickener may have adverse effects on each other due to different additives.
3）要在經常產生振動的場所、無塵室、真空、低溫或高溫等特殊環境下使用時，請使用符合規格?環境的潤滑脂。
3) When using in places that often generate vibration, clean rooms, vacuum, low or high temperature special environments, please use those that meet the specifications? Environmental lubricating grease.
4）對無油嘴和潤滑孔的產品進行潤滑時,將潤滑劑直接涂抹到滾動面上,以行程長度為單位進行數次跑合,使潤滑脂進入產品內部。
4) When lubricating products without nozzles or lubrication holes, apply the lubricant directly to the rolling surface and run in several times based on the stroke length to allow the grease to enter the interior of the product.
5）潤滑脂的稠度隨溫度而變化。滾珠絲杠的扭矩也隨稠度而變化,請注意。
5) The consistency of lubricating grease varies with temperature. The torque of the ball screw also varies with the consistency, please note.
6）加脂后潤滑脂的攪拌阻力,可能會導致滾珠絲杠旋轉扭矩增大。請務必進行跑合運轉，將潤滑脂進行充分跑合后，運轉機械。
6) The stirring resistance of the lubricating grease after greasing may cause an increase in the rotational torque of the ball screw. Please make sure to run in and fully run in the lubricating grease before operating the machine.
7）加脂完成后,多余的潤滑脂有可能向周圍飛濺,請根據需要進行擦拭。
7) After the greasing is completed, excess grease may splash around. Please wipe it as needed.
8）潤滑脂隨著使用時間的增長,性狀劣化,潤滑性能降低,所以需要根據使用頻率點檢并補充潤滑脂。
8) As the use of lubricating grease increases, its properties deteriorate and its lubrication performance decreases. Therefore, it is necessary to check and supplement the lubricating grease according to the frequency of use.
9）根據使用條件和使用環境不同,加脂時間間隔不同,請以每運行100km（3～6個月）為基準進行加脂。請根據實際設備,確定終的加脂時間間隔和加脂量。
9) According to different usage conditions and environments, the interval between greasing times varies. Please use every 100km (3-6 months) of operation as the benchmark for greasing. Please determine the final greasing interval and amount based on the actual equipment.
10）安裝方式和絲母的潤滑孔,可能致使潤滑油不循環造成潤滑不良,設請進行充分探討。
10) The installation method and lubrication hole of the screw nut may cause non circulation of lubricating oil and poor lubrication. Please fully explore this during design.
總之，使用滾珠絲杠時,必須提供良好的潤滑。如果以無潤滑狀態直接使用,可能會加快滾動部分的磨損,因而其使用壽命會縮短。更多相關事項就來我們網站http://www.zhzdh888.com咨詢！
In short, good lubrication must be provided when using ball screws. If used directly without lubrication, it may accelerate the wear of the rolling part, thus shortening its service life. For more related matters, come to our website http://www.zhzdh888.com consulting service
- 上一篇：有可能會影響聯軸器正常運轉的因素
- 下一篇：主軸組件發生故障怎么辦？
一文讀懂《傳動技術基...<>
導軌絲杠硬核解析：行...<>
機器人關節的核心密碼...<>
導軌絲杠新方案揭秘：...<>
導軌絲杠選型避坑：滾...<>
相關：
